Avago-technologies MegaRAID SAS 8204ELP Manuel d'utilisateur télécharger pdf

Thank you for purchasing the MegaRAID

SAS (Serial

Attached SCSI/Serial ATA II) 8204ELP RAID Controller or

the SAS 8208ELP (PCI Express Low-Profile) RAID

Controller. Before you install the RAID controller, please take

a few minutes to read this quick installation guide. If you

need more information about any topic covered in this guide,

refer to the related documents on your MegaRAID Universal

Software Suite CD.

Important: The SAS 8204ELP RAID Controller does not

contain the J6 (ports 4–7) connector. The missing

J6 connector is the only difference between the

SAS 8204ELP RAID Controller, which supports

one connector and four ports, and the SAS

8208ELP RAID Controller, which supports two

connectors and eight ports.

Important

: The RAID controller is a PCI Express x4 card, so

it fits only in a PCI Express x4 or larger slot.

Important

: SATA II is the only type of SATA supported by

these RAID controllers.

RAID CONTROLLER INSTALLATION

Step 1 Unpack the MegaRAID SAS RAID Controller

Unpack the RAID controller in a static-free

environment. Remove it from the antistatic bag,

and inspect it for damage.

If the RAID controller appears to be damaged, or

if the MegaRAID Universal Software Suite CD is

missing, contact LSI or your MegaRAID OEM

support representative.

The CD contains utility programs, device drivers

for various operating systems, and the following

documentation:

• MegaRAID SAS RAID Controllers User’s

Guide

• MegaRAID SAS Software User’s Guide

• MegaRAID SAS Device Driver Installation

User’s Guide

• Software license agreement

Step 2 Prepare the Computer

Turn off the computer, and unplug the power

cords from the rear of the power supply. Remove

the cover from the computer.

Step 3 Review the Jumpers and the Connectors

Figure 1 shows the location of the jumpers and

the connectors on the SAS 8208ELP RAID

Controller. The jumpers are set at the factory,

and you usually do not need to change them.

Figure 1 Layout of the MegaRAID SAS 8208ELP

RAID Controller

Back up your data before you change your

system configuration. Otherwise, you might lose

data.

CAUTION

Before you install the RAID controller, make sure

that the computer is disconnected from the power

and from any networks.

CAUTION

Port

4–7

Port

0–3

MegaRAID

SAS 8204ELP/

8208ELP RAID Controllers

Quick Installation Guide

1 2 3

Résumé du contenu

Page 1 - 8208ELP RAID Controllers

Thank you for purchasing the MegaRAID® SAS (Serial Attached SCSI/Serial ATA II) 8204ELP RAID Controller or the SAS 8208ELP (PCI Express Low-Profile) R

Page 2 - RAID Controller

2 of 3Table 1 describes the jumpers and the connectors on the RAID controller.Table 1 Jumpers and ConnectorsStep 4 Install the RAID ControllerInsert t

Page 3 - TECHNICAL SUPPORT

80-00118-01 Rev. C, January 2008Find a list of LSI Corporation’s U.S. distributors, international distributors, sales offices, and design resource cen

Modèles reliés MegaRAID SAS 8704EM2 | MegaRAID SAS 8704EM2 (Channel) | MegaRAID SAS 8708EM2 | MegaRAID SAS 8708EM2 (Channel) |

Commentaires sur ces manuels

Pas de commentaire

Avago-technologies MegaRAID SAS 8204ELP Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Avago-technologies MegaRAID SAS 8204ELP. Avago Technologies MegaRAID SAS 8204ELP User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés MegaRAID SAS 8704EM2 | MegaRAID SAS 8704EM2 (Channel) | MegaRAID SAS 8708EM2 | MegaRAID SAS 8708EM2 (Channel) |

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Avago-technologies MegaRAID SAS 8204ELP