Avago-technologies MegaRAID SATA 150-6 Manuel d'utilisateur télécharger pdf

Thank you for purchasing the MegaRAID SATA 150-6 RAID

Controller (RSA). Please take a few minutes to read this

quick installation guide before you install the controller. If you

need more information about any topic covered in this guide,

refer to the related documents on your MegaRAID Universal

Software Suite CD.

The MegaRAID SATA 150-6 supports the Battery Backup

Unit 01 (LSIBBU01). For more information about this battery,

refer to the MegaRAID Battery Backup Unit User’s Guide on

the MegaRAID Universal Software Suite CD.

MegaRAID SATA 150-6 RAID CONTROLLER

INSTALLATION

Step 1 Unpack the MegaRAID SATA 150-6 RAID

Controller

Unpack the controller in a static-free environment.

Remove it from the antistatic bag and inspect it

for damage.

If the controller appears to be damaged, or if the

MegaRAID Universal Software Suite CD is

missing, contact LSI Logic or your MegaRAID

OEM support representative.

The CD contains utility programs, device drivers

for various operating systems, and the following

documentation:

• MegaRAID SATA150 PCI to Serial ATA

Storage Adapters User’s Guide

• MegaRAID Configuration Software User’s

Guide

• MegaRAID Device Driver Installation User’s

Guide

• Software license agreement and warranty

registration card

Step 2 Prepare the Computer

Turn off the computer and unplug the power

cord(s) from the back of the power supply.

Remove the cover from the chassis.

Step 3 Review the Jumpers and Connectors

Figure 1 shows the location of the jumpers and

the connectors on the MegaRAID SATA 150-6

RAID Controller. The jumpers are set at the

factory, and you usually do not need to change

them.

The Write Pending connector (J4) provides a

signal that indicates that the on-board cache

contains data and a write from the cache to the

hard drives is pending.

Figure 1 MegaRAID SATA 150-6 RAID Controller

Card Layout

Back up your data before you change your

system configuration. Otherwise, you might lose

data.

CAUTION

Before you install the controller, make sure that

the computer is disconnected from the power and

from any networks.

CAUTION

J1 J2 J3

J4 J5 J6

J13

J14

J16

J17

Port 0 Port 1 Port 2 Port 3 Port 4 Port 5

J7 J8 J9 J10 J11 J12

LSI Logic MegaRAID

SATA 150-6 RAID Controller

Quick Installation Guide

1 2 3

Résumé du contenu

Page 1 - SATA 150-6 RAID Controller

®Thank you for purchasing the MegaRAID SATA 150-6 RAID Controller (RSA). Please take a few minutes to read this quick installation guide before you in

Page 2 - RAID Controller

2 of 3Ta bl e 1 describes the jumpers and the connectors on the controller.Step 4 Install the MegaRAID SATA 150-6 RAID Controller on the MainboardIns

Page 3 - TECHNICAL SUPPORT

PN 80-00095-01 Rev. B, June 2006Find a list of LSI Logic Corporation’s U.S. distributors, international distributors, sales offices, and design resour

Commentaires sur ces manuels

Pas de commentaire

Avago-technologies MegaRAID SATA 150-6 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Avago-technologies MegaRAID SATA 150-6. Avago Technologies MegaRAID SATA 150-6 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Avago-technologies MegaRAID SATA 150-6