Avago-technologies MegaRAID SAS 8704ELP Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Avago-technologies MegaRAID SAS 8704ELP. Avago Technologies MegaRAID SAS 8704ELP User Manual Manuel d'utilisatio
- Page / 3
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Thank you for purchasing the LSI MegaRAID NiMH
intelligent Battery Backup Unit 05 (iBBU05). The iBBU05 is
designed for use on MegaRAID SAS RAID controllers.
It protects the integrity of the cached data on a MegaRAID
controller for up to 72 hours in the event of a complete AC
power failure or a brief power outage.
This quick installation guide explains how to install the
iBBU05 on the MegaRAID SAS 8704ELP, SAS 8708ELP,
and SAS 8888ELP controllers.
LSI provides a family of MegaRAID intelligent battery backup
units (iBBUs) for use with its high-performance MegaRAID
RAID controllers. The LSI MegaRAID iBBUs provide an
inexpensive alternative to using an uninterruptible power
supply (UPS) and a second level of fault tolerance when
used in conjunction with a UPS.
Figure 1 shows the top view and the bottom view of the
iBBU05, the M2.50-0.45 x 5mm screws, and the 6mm
standoffs. (The “top” side is the side that you can see after
you install the LSIiBBU05 on the RAID controller.) Note that
this unit combines a battery pack with a daughtercard.
Figure 1 LSIiBBU05 and Components
1 - J2 Battery Pack Harness Connector
2 - J1 Connector
3 - J14 Board-to-board Connector
4 - Battery Pack Harness
Important
: For detailed information about this battery, see
the Intelligent Battery Backup Unit for 1078-based
MegaRAID Products Guide.
Installing the iBBU05 on the SAS
8704ELP or SAS 8708ELP RAID Controller
Follow these steps to install the iBBU05 on the SAS
8704ELP RAID controller or on the SAS 8708ELP RAID
controller. The battery is installed on the top of the controller.
Step 1 Ground yourself, and remove the iBBU05
daughter card from the package.
Step 2 Insert the battery pack harness connector at the
end of the colored wires into the 5-pin J2
connector on the backside of the iBBU05.
Step 3 Place the iBBU05 front-side-up on a flat, clean,
static-free surface.
Step 4 With the front side up, place the MegaRAID SAS
RAID controller on a flat, clean, static-free
surface.
Step 5 Hold the iBBU05 daughtercard so that the battery
side is up and the J14 connector lines up with the
J7 BBU connector on the SAS 8704ELP RAID
Electrostatic discharge can damage the iBBU05
and the MegaRAID SAS RAID controller. Make
sure that you install the iBBU05 at an ESD-safe
workstation that meets the requirements of EIA-
625 – “Requirements For Handling Electrostatic
Discharge Sensitive Devices.” When you install
the iBBU05, follow the ESD-recommended
practices in the latest revision of IPC-A-610.
There is danger of an explosion if the battery is
incorrectly replaced. Replace it only with the
same or equivalent type recommended by the
manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
!
CAUTION
WARNING
!
MegaRAID
®
iBBU05 Battery
Backup Unit
Quick Installation Guide
Résumé du contenu
Page 1 - Backup Unit
Thank you for purchasing the LSI MegaRAID NiMH intelligent Battery Backup Unit 05 (iBBU05). The iBBU05 is designed for use on MegaRAID SAS RAID contro
Page 2
2 of 3controller or on the SAS 8708ELP RAID controller, as shown in Figure 2.Figure 2 Installing the iBBU05 Daughtercard on the SAS 8708ELP RAID Contr
Page 3 - TECHNICAL SUPPORT
80-00164-01 Rev. C, July 2008Find a list of LSI Corporation’s U.S. distributors, international distributors, sales offices, and design resource center
Produits connexes et manuels pour Matériel Avago-technologies MegaRAID SAS 8704ELP
(3 pages)
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.463 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels